| P-60 | |
|---|---|
| Curtiss XP-60C in flight, modified from second XP-60A, with Pratt & Whitney R-2800 engine and contra-rotating propellers. | |
| Role | Fighter aircraft |
| Manufacturer | Curtiss-Wright |
| First flight | 18 September 1941 |
| Retired | 22 December 1944 |
| Status | Cancelled |
| Primary user | United States Army Air Forces |
| Produced | 1942-1944 |
| Number built | 5 (all converted into new variants)[1] |
| Program cost | $8.88 million USD[2] |
| Developed from | Curtiss XP-46 Curtiss XP-53 |
The Curtiss P-60 was a 1940s United States single-engine single-place, low-wing monoplane fighter aircraft developed by the Curtiss-Wright company as a successor to their P-40. It went through a lengthy series of prototype versions, eventually evolving into a design that bore little resemblance to the P-40. None of these versions reached production.
Contents |
The initial design contained in proposals to the United States Army Air Corps was for an aircraft based upon the P-40 design but featuring a low drag laminar flow wing, a Continental XIV-1430-3 inverted vee engine, and eight wing-mounted 0.5 in (12.7 mm) machine guns. This proposal was accepted and a contract for two prototypes was issued on 1 October 1940 with the aircraft designated the XP-53.
Within two months the Army Air Corps modified the contract to require the second prototype be completed with a Rolls-Royce Merlin engine in place of the XIV-1430. That aircraft was re-designated XP-60. The airframe design for the XP-60 was modified for the different engine, and the main landing gear was changed from the rearward retracting P-40 design to a new inward retracting version, which allowed a wider wheelbase and a smooth wing surface when the gear was retracted. This aircraft first flew on 18 September 1941 with a British-built Merlin 28 engine. The XP-53 prototype was then converted into a static test airframe for the XP-60.
Considering delivery delays of quantities of the Packard-built Merlin engines due to its use in other fighters, the use of a turbo-supercharged Allison V-1710-75 engine was considered in its place. Consequently, on 31 October 1941, a contract for 1,950 P-60A fighters using the Allison engine, was awarded.
In the meantime, flight tests of the XP-60 prototype were not progressing smoothly. In addition to landing gear problems, expected top speed was not being met due to shortcomings in the laminar-flow wing surface finish, relatively high radiator drag (compared to the North American P-51 Mustang, which was then flying), and less than specified engine output performance. Consequently, work on the P-60A was stopped on 20 December 1941, when the USAAC recommended that Curtiss concentrate on licence production of Republic P-47 Thunderbolts.[3]
On 2 January 1942 the order was changed to produce one XP-60A with the Allison V-1710-75 engine and a General Electric B-14 turbo-supercharger, one XP-60B with the Allison V-1710-75 engine and a Wright SU-504-1 turbo-supercharger, and one XP-60C with the massive Chrysler XIV-2220 sixteen cylinder inverted vee engine.
At the time, availability of the Chrysler engine was coming into question, and after Curtiss noted that several hundreds of pounds of lead would be needed in the tail of the existing airframe for balance, a decision was made to install a Pratt & Whitney R-2800 radial engine in the XP-60C. In the meantime, Curtiss installed a Merlin 61 engine in the original XP-60 and after enlarging the vertical tail surface, this aircraft was re-designated XP-60D.
The XP-60A first flew on 1 November 1942. While official interest in the P-60 waned during summer 1942, interest due to the promise of improved performance with the installation of the R-2800 engine resulted in a contract for 500 R-2800 powered P-60A-1-CU fighters with contra-rotating propellers. With concern that the contra-rotating propellers would not be available on time, the XP-60B was modified to take the R-2800-10 engine driving a four-bladed propeller. This modification was re-designated XP-60E.
On 27 January 1943, the XP-60C flew for the first time, powered by a R-2800-53 engine with contra-rotating propellers. The aircraft's flying characteristics were found to be generally satisfactory. The first flight of the XP-60E with the four-bladed propeller, was delayed until 26 May 1943 after it was found that due to its lighter weight, the engine installation had to be moved 10 inches forward compared to the XP-60C.
In April 1943, the US Army Air Force decided to conduct an evaluation of the various fighter aircraft in development and use, in order to eliminate the least desirable models. Curtiss was requested to have the XP-60E participate. As the XP-60E was not available, the company hurriedly prepared the XP-60C for the evaluation at Patterson Field. In the event, due to various issues, the XP-60C performed poorly, resulting in reduction of the production run of 500 aircraft to two aircraft.[4]
In January 1944, the XP-60E was flown to Eglin Field for official trials, where Army Air Force pilots found that it did not compare favorably to contemporary aircraft designs. When Curtiss expressed the desire to abandon further work on the P-60 series, the Army Air Force insisted upon completion of one of the two aircraft in production. The aircraft when originally ordered was designated YP-60A-1-CU was re-designated YP-60E. This aircraft flew on 13 July 1944 and was subsequently delivered to Wright Field. The YP-60E differed mainly from the XP-60E in being powered by a 2,100 hp (1,566 kW) R-2800-18 engine as well as the fitting of an all-round vision bubble canopy.
With the development contracts cancelled in June 1943, the program ended ignobly when the last prototype was scrapped on 22 December 1944.[4]To replace the P-60, Curtiss built 354 Republic P-47Gs instead for the USAAF.[1] The XP-60E survived to be sold as an entry for the 1947 National Air Races, but crashed during a qualifying flight before the competition was held. [5]
General characteristics
Performance
Armament
|
||||||||
|
||||||||||||||
|
||||||||||||||